Manufacturing
Where ideas become physical.
A drawing is only the beginning.
Exceptional environments depend on thousands of components being manufactured accurately, consistently and at the right moment.
Método integrates manufacturing into the delivery process so design intent survives the journey from drawing to installation.
Control
Greater control where it matters.
- Quality
- Programme
- Cost
- Consistency
- Repeatability
- Replacement
- Scale
Capabilities
Joinery
Furniture
Kitchens
Doors
Stone
Metalwork
Upholstery
GRP / GRC
Architectural components
Specialist fabrication
From prototype to production
Test once.
Make with confidence.
Samples, technical drawings, prototypes and full-size mock-ups settle tolerance, finish and assembly before a production run begins.
Once approved, the standard is fixed and every subsequent component is measured against it.
Making
From three hundred guest rooms
to a single villa.
The same disciplines answer a repeated hotel room package, a private house and a themed environment — held to one benchmark, made by people whose hands are on the work.
Fine joinery
Hand-finished
Curved and veneered joinery, wall panelling, reception and bar fronts, hand-finished to an approved benchmark.
Bench-made & benchmarked
Furniture & casegoods
Room to programme
From one villa's dining table to a full guest-room package repeated across hundreds of keys without drift.
Bespoke & repeatable
Upholstery & soft furnishing
Atelier-made
Frames, foams, leathers and textiles built and stitched by hand, with wear and cleaning specified for use.
Hand-stitched
Stone & surfaces
Slab-selected
Slab selection, dry-lay, book-matching and hand-honed edge profiles before anything reaches site.
Block to book-match
Architectural metal & glass
Patinated by hand
Bronze and brass screens, trims, balustrades and feature glazing, finished and patinated by hand.
Screens, trims, feature
Decorative composites
Moulded & modelled
Domes, cornices, screens and themed geometry modelled, moulded and finished for interior and facade.
GRC · GRP · GRG
Composites division
GRC. GRP. GRG.
Geometry without limits.
Glassfibre reinforced concrete, polymer and gypsum let architecture take shapes that stone, plaster or metal cannot hold at scale — domes, screens, cornices, curved cladding and themed geometry, produced light enough to install and durable enough to last.
- Glassfibre reinforced concrete
- Glassfibre reinforced polymer
- Glassfibre reinforced gypsum
GRC
Glassfibre reinforced concrete
High-strength glass fibre in a cementitious matrix. Non-combustible, corrosion-free and mouldable into intricate patterns, deep relief and sweeping curves. Cast in integral colour and texture — limestone, precast, acid wash or paint grade.
- Facade & cladding panels
- Screen walling & mashrabiya
- Cornices, mouldings & corbels
- Domes, columns & pilasters
- Balustrades & gate piers
- Fountains, planters & landscape
GRP
Glassfibre reinforced polymer
Lightweight, waterproof and impact-resistant composites for themed and sculptural work, signage, pods and linings — formed to any geometry and finished to a controlled surface standard.
- Themed & sculptural elements
- Feature signage
- Water features & pool details
- Tank, roof & manhole lining
- Bespoke enclosures & pods
- Waterproofing systems
GRG
Glassfibre reinforced gypsum
Interior-grade composite for seamless ceilings, coffered domes and fine decorative profiling — dimensionally stable, paint-ready and installed as prefabricated modules.
- Coffered & feature ceilings
- Interior domes & vaults
- Cornices & decorative profiling
- Column casings
- Wall panelling
- Bespoke interior mouldings
Engineering the element
Every panel is engineered before it is cast.
Shop drawings
Panel setting-out, joints, laminate build-up and sequence instructions.
Structural calculations
Load transfer, embedded frames, fixing integrity and deflection.
Mould & pattern design
Tooling, repeat strategy and surface finish control.
Installation drawings
Fixing detail, substrate flatness, installation gap and tolerances.
Manufactured to
Sourcing & supply
Specified, sourced and made under one accountability.
Materials & finishes
- Stone & engineered surfaces
- Timber, veneer & solid wood
- Stainless steel sheet & trims
- Glass, mirror & partitions
- LVT, SPC & timber flooring
- WPC decking & external finishes
Manufactured packages
- Fixed & loose FF&E
- Fire-rated and timber doorsets
- Wardrobes, kitchens & vanities
- Bespoke light fittings
- Architectural metalwork & screens
- GRP / GRC feature elements
Control & assurance
- Prototype and first-article approval
- In-factory QA / QC inspection
- ISO-aligned quality management
- Mock-up rooms & benchmark suites
- Container loading & logistics control
- Site installation teams
Quality
Quality is not inspected in.
It is built in.
Checks sit inside the process — at material receipt, at machining, at assembly, at finishing and at packing — not only at the end.
Defects are caught where they are cheap to correct, in the workshop, rather than on a live site with an opening date.